你的位置:首頁 > 測試測量 > 正文

PCB設計規則中英文對照一覽

發布時間:2020-02-13 責任編輯:xueqi

【導讀】今天分享一些PCB設計規則的中英文對照,來看看你都知道哪些吧!
 
PCB設計規則中英文對照
 
 
Electrical(電氣規則):
 
Clearance:安全間距規則
 
Short Circuit:短路規則
 
UnRouted Net:未布線網絡規則
 
UnConnected Pin:未連線引腳規則
 
 
Routing(布線規則):
 
Width:走線寬度規則
 
Routing Topology:走線拓?fù)洳季忠?guī)則
 
Routing Priority:布線優先級規則
 
Routing Layers:布線板層線規則
 
Routing Corners:導線轉角規則
 
Routing Via Style:布線過孔形式規則
 
Fan out Control:布線扇出控制規則
 
Differential Pairs Routing:差分對布線規則
 
 
SMT(表貼焊盤規則):
 
SMD To Corner:SMD焊盤與導線拐角處最小間距規則
 
SMD To Plane:SMD焊盤與電源層過孔最小間距規則
 
SMD Neck Down:SMD焊盤頸縮率規則
 
 
Mask(阻焊層規則):
 
Solder Mask Expansion:阻焊層收縮量規則
 
Paste Mask Expansion:助焊層收縮量規則
 
 
Plane(電源層規則):
 
Power Plane Connect Style:電源層連接類型規則
 
Power Plane Clearance:電源層安全間距規則
 
Polygon Connect Style:焊盤與覆銅連接類型規則
 
 
TestPoint(測試點規則):
 
Testpoint Style:測試點樣式規則
 
TestPoint Usage:測試點使用規則
 
 
Manufacturing(工業規則):
 
MinimumAnnularRing: 焊盤銅環最小寬度規則,防止焊盤脫落。
 
Acute Angle:銳角限制規則
 
Hole Size:孔徑限制規則
 
Layer Pairs:配對層設置規則,設定所有鉆孔電氣符號(焊盤和過孔)的起始層和終止層。
 
Hole To Hole Clearance:孔間間距桂鄂
 
Minimum SolderMask Sliver:最小阻焊間隙違反規則
 
Silkscreen Over Component Pads:絲印與元器件焊盤間距規則
 
Silk To Silk Clearance:絲印間距規則
 
Net Antennae:網絡天線規則
 
 
High Speed(高頻電路規則):
 
ParallelSegment:平行銅膜線段間距限制規則
 
Length:網絡長度限制規則
 
Matched Net Lengths:網絡長度匹配規則
 
Daisy Chain Stub Length:菊花狀布線分支長度限制規則
 
Vias Under SMD:SMD焊盤下過孔限制規則
 
Maximum Via Count:最大過孔數目限制規則
 
 
Placement(元件布置規則):
 
Room Definition:元件集合定義規則
 
Component Clearance:元件間距限制規則
 
Component Orientations:元件布置方向規則
 
Permitted Layers:允許元件布置板層規則
 
Nets To Ignore:網絡忽略規則
 
Hight:高度規則
 
 
Signal Integrity(信號完整性規則):
 
Signal Stimulus:激勵信號規則
 
Undershoot-Falling Edge:負下沖超調量限制規則
 
Undershoot-Rising Edge:正下沖超調量限制規則
 
Impedance:阻抗限制規則
 
Signal Top Value:高電平信號規則
 
Signal Base Value:低電平信號規則
 
Flight Time-Rising Edge:上升飛行時間規則
 
Flight Time-Falling Edge:下降飛行時間規則
 
Slope-Rising Edge:上升沿時間規則
 
Slope-Falling Edge:下降沿時間規則
 
Supply Nets:電源網絡規則
要采購焊盤么,點這里了解一下價格!
特別推薦
技術文章更多>>
技術白皮書下載更多>>
熱門搜索
?

關閉

?

關閉